A 3D model of a grow tent. Change the clip fans, the exhaust and the light, and see where the light lands, how air, heat and water vapor move through the canopy, and how warm the leaves run.
About this tool: how the model works and where its numbers come fromThis is a computer model built from published research on airflow, grow lights and leaves. It hasn't been tested against a real tent yet. We plan to compare it with sensor readings from a running tent and will update it then.
Saved Builds
An account saves your build as you go and keeps named builds to load later.
Sign inSaved Setups
A Pro plan loads a layout saved in the Airflow Planner (room size, HAF fans, exhaust fans and vents) or a light fixture saved in the Grow Light Planner (size, watts, efficacy and spectrum) in place of the tent settings above. It also shows the light on every leaf, down through the canopy, with uniformity as in the planner's light map.
Sign in See ProRooms up to 15 × 15 ft with a ceiling up to 10 ft.
The tent is split into cubes about 2 in on a side. In every cube the model solves air movement, temperature and water vapor as they change over time. The air paths and the slice show an 8 second average unless you pick Live. Bigger rooms from the Airflow Planner use bigger cubes, so a step still runs in about a twentieth of a second.
Air is treated as incompressible, with buoyancy from warm and moist air. Clip fans push their set airflow through a 6 in disc. The exhaust pulls the same airflow out through the carbon filter (or through the wall fans of a saved layout) that comes in at the intake. A second fan can add to the exhaust, or run as a scrubber: it pulls air through its own carbon filter and blows it back into the tent from the fan on the filter's end, so it moves air around without changing how much leaves. Growth stage sets each plant's height, width and leaf density: a plant in veg is about half the height and 70% of the width of one in flower, with 80% of the leaf density, and a seedling is far smaller (Bizon estimates). The canopy slows air with a drag coefficient of 0.2 on its leaf area, and surfaces add friction to the air beside them.
Each watt of the fixture is split into blue and red light, green light, near infrared, thermal infrared radiated down, and heat into the air at the fixture. The split comes from Nelson and Bugbee (2015), who measured each band under HPS and LED at the same light level. The LED settings are scaled to a 2.7 µmol/J fixture: 53% light, 3% near infrared, 5% thermal infrared and 40% heat into the air. The HPS is 1.7 µmol/J: 35% light, 22% near infrared, 22% thermal infrared and 21% heat into the air. A saved fixture uses its own efficacy and its blue, green, red and far-red shares.
The light reaching the top of the canopy comes from the Grow Light Planner's model: each fixture is split into small emitters with a cosine beam, and Mylar walls return part of the light that misses the canopy. Its average matches the light the model delivers, so the map sets where light lands. Leaves under a bright spot absorb more, open their stomata wider, run warmer and lose more water. Uniformity is the lowest point divided by the average over the standard grid of points, leaving out the strip along the walls. Below the top, each layer of leaves takes its share and passes the rest down. Light that reaches the floor bounces back up (half of it in a Mylar tent) and lights the lower leaves from below. With a Pro plan, Color: Light shows the light in every part of the tent and on every leaf.
Each band is absorbed layer by layer down through the leaves (Beer's law, k = 0.7, a general value for broad-leaved crops). Leaves absorb 92% of blue and red light and 80% of green (Zhen, Kusuma and Bugbee), and 26% of near infrared and 97% of thermal infrared (Nelson and Bugbee). Near infrared reaches deepest. What gets through heats the pot tops and floor. Mylar walls return most of the light that reaches them.
Every cube with leaves has its own leaf temperature from an energy balance. Absorbed radiation leaves as heat from both leaf surfaces, as transpiration, and as thermal infrared where leaves see out of the canopy. Leaf boundary layers follow Nelson and Bugbee. Stomatal conductance is at most 0.5 mol/m²/s, the high end for well-watered plants. Stomata open with light, half open at 300 µmol/m²/s, since cannabis stomata keep opening up to 2,000 (Chandra et al.), and close as leaf VPD rises. Transpiration is shown per day at the lights-on rate.
The fabric passes heat to the room at 3.5 W per m² per °C of difference. Heat and water are carried between cubes so that, once the tent settles, the heat added equals the heat that leaves. The Heat row shows that balance.
These values are Bizon estimates without a published source yet: the canopy k for cannabis, how fast stomata close as VPD rises, the green share of the default spectra, the tent fabric's heat loss, and the HPS hood's 110° beam.
Sources: Nelson and Bugbee (2015) for fixture radiation, leaf absorptance and leaf boundary layers. Zhen, Kusuma and Bugbee for green light absorptance. Chandra et al. for the cannabis stomatal response. Canopy speed bands match the Airflow Planner.